Getting Familiar with Plumbing: The First Step for Bathtub Installation
Getting Familiar with Plumbing: The First Step for Bathtub Installation
Blog Article
They are making a few great points related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in the article down the page.
![Installing A Bathtub](https://www.myjobquote.co.uk/assets/img/cost-of-installing-a-new-bath-1.jpg)
Mounting a bath tub isn't precisely rocket science, but it does need strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably tough job. If the old tub is conveniently available, the task can relocate speedily; if you need to open up a wall surface to remove the old tub as well as position the brand-new bath tub, the job is much harder. In either case, the job is within a home handyman's skills, although you will certainly require a helper to vacate the old bathtub and set in the brand-new one. Make sure you have actually certified on your own for the work and are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Possibilities are you may need a specialist plumber to make tube links.
This post will aid you install a new tub in your washroom if you have actually already bought a new tub as well as do not need to change the plan of your previous water system pipelines.
Your devices and also product checklist must consist of the following:
Preparing for the Installment
To start with, the sustaining structure supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to prevent stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets using 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water. After doing so, switch on the faucets to drain any type of water staying in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted access that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the needed position. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little points.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by checking the level as well as changing the feet on the tub up until the spirit level reads degree.
To install taps, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; after that do the very same for the other tap.
Turn on the water supply and inspect all joints and also new pipework for leaks as well as tighten them if necessary. Load the bathtub and additionally inspect the overflow outlet as well as the regular electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has been used a minimum of when as this will resolve it into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in place between the tap as well as the sink. Secure the faucet in position with the supplier given backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet connectors. The previous type needs to be connected to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a stiff seal, triggering the water to permeate the wall in between the bath as well as the tiling, causing difficulties with wetness and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes as well as cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to permit the activity experienced when the bathtub is in usage. The sealer can split relatively early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the tiles making use of water-resistant or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
![How to Install a Bathtub](https://i0.wp.com/petalspiesandotherwise.com/wp-content/uploads/2019/10/Freestanding-Tub-Install-3.jpg?resize=680%2C510)
I am very interested by Installing A Bathtub and I really hope you enjoyed the blog post. Are you aware of somebody who is curious about the niche? Feel free to share it. Many thanks for going through it.
For fast action, contact! Report this page